This screen uniformity test fills your screen with flat greys and colors, so uneven areas stand out: darker corners, brighter zones, tinted patches, clouding and the bands of the dirty screen effect. It starts on 50% grey, then steps through a zone grid, dark and light greys, white and the three primary colors.
It works on monitors, laptops, TVs and phones in any browser. Mark every problem area and copy the report, which lists where each mark is, for a return or a warranty claim.
How to test screen uniformity
- Let the screen warm up for at least 15 minutes. Uniformity changes as an LCD panel warms.
- Set brightness to your normal level and turn off any eye care, dynamic contrast or local dimming modes for the first pass.
- Press Start full screen test and sit centered, eyes level with the middle of the screen, at your normal distance.
- Look at the whole screen at once rather than scanning it. Uneven areas pop out that way.
- Press M on any patch, tint or band to mark it. Press Space for the next pattern.
- Press Esc at the end and copy the report.
For the dirty screen effect, scroll a light grey page slowly while you look at it, or turn your head a little. Fixed bands that stay put as things move over them are DSE.
What each pattern shows
| Pattern | Best for |
|---|---|
| Grey 50% | Patches, dark corners, blotches and DSE |
| Uniformity grid | Comparing each zone with the center |
| Grey 25% and 10% | Clouding and backlight problems on LCDs, near black faults on OLED |
| Grey 5% | Clouding and bleed in a dark room |
| Grey 75% and white | Tints, yellow or pink zones, bright spots |
| Red, green and blue | Color shifts in one channel, and stuck sub-pixels |
Darker corners or edges
Most screens are a little darker toward the edges, especially large and curved ones. It is a problem when one corner is clearly darker than the others or a dark area cuts across the picture.
- Check from your normal seat. On IPS panels, looking from up close adds glow, and on VA panels the edges darken from close up. Sit back and test again.
- On a curved screen, sit at the center of the curve, usually 60 to 100 cm away.
- If one corner stays darker, compare it with the other three on the uniformity grid and mark it.
Tinted zones: pink, green or yellow areas
A patch with a color cast is a color uniformity fault. It shows best on white and light grey.
There is no setting that fixes it, because it comes from the panel or backlight itself. On a new screen, return it within the return window. Some monitors have a uniformity compensation mode in their menu, which reduces the variation at the cost of some brightness.
Clouding and blotches on dark grey
Cloudy, lighter patches on 10% or 5% grey come from pressure on the LCD panel or an uneven backlight. They are common on edge lit LCDs and show in dark films and games.
The edges of the screen leaking light on black is backlight bleed, a related fault with its own backlight bleed test. Mini LED screens with local dimming can also show blooming around bright objects, which is a different effect.
Vertical bands and the dirty screen effect
Faint vertical or horizontal bands on mid grey, which stay put as the picture moves, are the dirty screen effect. It is common on large TVs and some OLEDs.
- Look at moving content: a football pitch or a sky in a slow pan shows it best.
- On an OLED, run the pixel refresh or panel care cycle from the settings menu, which can reduce banding and temporary retention.
- If the bands are strong in normal viewing, an exchange is the only fix.
Ghost images of logos or taskbars on OLED are burn-in or retention, which the oled burn in test separates.
Before you return a screen
- Test after warm up, from your normal seat, at your normal brightness.
- Mark each problem and copy the report.
- Take a photo of the worst pattern with your phone at a low exposure, so the photo is not brighter than what you see.
- Check for dead pixels at the same time with the dead pixel test, since sellers often accept one claim for several faults.
What a uniformity test cannot measure
Your eyes judge the patterns, and cameras exaggerate or hide uneven areas. Measuring uniformity in numbers takes a colorimeter that reads each zone of the screen.
The patterns are drawn in standard dynamic range. A screen can look even on these greys and still show blooming or uneven HDR highlights. For gradients and steps rather than flat colors, use the color banding test online.
Screen uniformity questions
What is screen uniformity?
Uniformity is how evenly a screen shows one color across its whole area. On a perfect screen a grey looks the same in the corners as in the middle. Real screens are a little darker at the edges, and poor ones show patches, tints or bands.
What is the dirty screen effect?
The dirty screen effect, or DSE, is a pattern of faint smudges and vertical or horizontal bands that looks like a dirty window. It shows most when a flat, light color moves across the screen, such as a sports field or a sky when the camera pans.
How much uniformity variation is normal?
Most monitors measure 5 to 10% darker in the corners than in the center, which is hard to see in normal use. If you notice a patch or tint on a white web page or a grey background without looking for it, it is worth an exchange on a new screen.
Which monitors give the most consistent color across the screen?
Monitors with factory uniformity compensation are the most even, such as professional models from Eizo, ASUS ProArt, BenQ SW and Dell UltraSharp that measure and correct each zone at the factory. OLED screens have very even brightness but can tint at dark greys. Reviews that measure gray uniformity are the best guide for a given model.
Why does my screen look pink on one side and green on the other?
That is color uniformity, also called tint shift. Parts of the panel or backlight have a slightly different color. It is common on large IPS panels and some OLEDs and cannot be fixed with settings, only by an exchange.
Should I test uniformity with a grey screen or a white screen?
Use both. Mid grey shows patches and DSE best, dark grey shows clouding and backlight problems, and white shows tints and yellowing. This test steps through all of them.
Can uniformity get better with use?
Rarely. Some clouding on new LCDs eases a little as the panel warms up, so test after 30 minutes of use. On an OLED, faint patches that appear after use can be image retention, which usually clears after the screen runs its refresh cycle.